THE IMPORTANCE OF PH IN THE POOl
The ideal pH value in the pool is between 7.0 and 7.6. At this value, the water does not cause any irritation or limescale deposition, and the efficiency of the chemical products with which you treat the pool water is optimized. Among other things, PVC coating or liner remains in good condition for a long time.
A pH below 7.0 will cause side effects, the most significant of which are corrosion of metal parts in the pool and irritation of the eyes and mucous membranes. pH higher than 7.6, (hard water), causes irritation of the eyes and mucous membranes, while the air smells familiar "chlorine odor". In addition, it will cause the formation of dangerous and unaesthetic scale deposits on the stairs and liner, the water has a "milky appearance", and will significantly reduce the efficiency of chemical products for water treatment. Among other things, it can lead to problems in the functioning of the filtration system. With a sand filter, there is a risk of limescale settling in the inner bed of sand.
MAINTENANCE OF PVC LINING
To keep the PVC coating or liner in excellent condition for several years, it is necessary to perform the following actions: Avoid leaving earth, metal and glass parts in the water so as not to damage it mechanically remove limescale deposits on the sides of the pool and pay special attention to places along the surface water line is particularly sensitive to various sediments such as scale, greasy products, dirt residues, sunscreens and smog that are dried and fixed under the sun’s rays. in case of moderate use of sunscreen and oil, bathers must not enter the pool 30-45 minutes after applying them, and they MUST SHOWER before each entry into the pool.
WATERLINE CLEANING
In the skimmer type of pool, the water level is 10-15 cm lower than the level of the beach or the edge stone. As the water line is created between water and air, it should be thoroughly cleaned with special mild sponges for this purpose, and by no means with chemical solvents, thinners and aggressive
agents for general use that could damage the foil.
Pool maintenance
After backwashing the filter by turning the multiple valve lever to the RINSE position, the filter sleeve is re-formed. The duration of the formation of the filter liner is about 15 - 30 seconds or until it appears clean.
THE MULTIPLE VALVE SHOULD NEVER TURN WHILE THE PUMP IS IN FUNCTION !!!
MULTIPLE VALVE POSITIONS
To switch from one position to another, it is necessary to stop the pump, press the lever, and turn the lever clockwise to the desired position.
WINTER POOL MAINTENANCE
General rules:
More info Click Here
The ideal pH value in the pool is between 7.0 and 7.6. At this value, the water does not cause any irritation or limescale deposition, and the efficiency of the chemical products with which you treat the pool water is optimized. Among other things, PVC coating or liner remains in good condition for a long time.
A pH below 7.0 will cause side effects, the most significant of which are corrosion of metal parts in the pool and irritation of the eyes and mucous membranes. pH higher than 7.6, (hard water), causes irritation of the eyes and mucous membranes, while the air smells familiar "chlorine odor". In addition, it will cause the formation of dangerous and unaesthetic scale deposits on the stairs and liner, the water has a "milky appearance", and will significantly reduce the efficiency of chemical products for water treatment. Among other things, it can lead to problems in the functioning of the filtration system. With a sand filter, there is a risk of limescale settling in the inner bed of sand.
MAINTENANCE OF PVC LINING
To keep the PVC coating or liner in excellent condition for several years, it is necessary to perform the following actions: Avoid leaving earth, metal and glass parts in the water so as not to damage it mechanically remove limescale deposits on the sides of the pool and pay special attention to places along the surface water line is particularly sensitive to various sediments such as scale, greasy products, dirt residues, sunscreens and smog that are dried and fixed under the sun’s rays. in case of moderate use of sunscreen and oil, bathers must not enter the pool 30-45 minutes after applying them, and they MUST SHOWER before each entry into the pool.
WATERLINE CLEANING
In the skimmer type of pool, the water level is 10-15 cm lower than the level of the beach or the edge stone. As the water line is created between water and air, it should be thoroughly cleaned with special mild sponges for this purpose, and by no means with chemical solvents, thinners and aggressive
agents for general use that could damage the foil.
Pool maintenance
After backwashing the filter by turning the multiple valve lever to the RINSE position, the filter sleeve is re-formed. The duration of the formation of the filter liner is about 15 - 30 seconds or until it appears clean.
THE MULTIPLE VALVE SHOULD NEVER TURN WHILE THE PUMP IS IN FUNCTION !!!
MULTIPLE VALVE POSITIONS
- FILTRATION - FILTRATION
- BACKWASH - WASH FILTER
- RINSE - RINSE THE FILTER
- .WASTE - POOL DISCHARGE
- RECIRCULATION - WATER CIRCULATION WITHOUT FILTER
- CLOSED
To switch from one position to another, it is necessary to stop the pump, press the lever, and turn the lever clockwise to the desired position.
WINTER POOL MAINTENANCE
General rules:
- keep the water clear and clean
- Never leave any objects in the pool
- maintain normal water level min. 1/2 to the max. 2/3 of the height of the skimmer opening
- do not empty the pool of water
- protect cold-sensitive parts
- in case of freezing of the water surface, do not break the ice
More info Click Here
No comments:
Post a Comment